Order Now
uses propane, natural gas, or hydrogen with oxygen to create a wide range of flame characteristics for flameworking applications.
Surface Mixed:
The WildCat Burner is surface mixed. Surface mixed burners deliver the gas and oxygen to the face separately so that the mixing of gases happens as they exit the burner face. This produces a safe flame for working with most flameworking applications. Surface mixed burners have a much lowered possibility for combustion to take place inside of the burner (this is commonly known as Flashback) since the gas and oxygen are not mixed until they exit the burner. However, certain conditions (such as an internal leak) could cause a Flashback to occur. It is always recommended to use flashback safety devices (i.e. flashback arrestors or fire checks) with any flameworking system.
| Order# | Description | Price |
| WildCat | Carlisle WildCat | $420.00 |
| Torch Mounted Marvering Pad Under Development |
$TBA |
More Detailed Instructions Below!
Control Valves:
Standard models require two valves which are, located on the back of the WildCat Burner.
Vortex Cooling Feature:
Built into the end of the WildCat burner is the Vortex cooling feature. This feature uses pressurized oxygen from the oxygen manifold to inspirate atmospheric air through the collar at the end of the burner. The mixture of oxygen and air both support the flame and cool the end of the burner. The more oxygen used, the more effective this cooling feature becomes. If the WildCat is found to be overheating, inspect the cooling features porting to ensure that there are no blockages.
Flame Atmospheres:
The WildCat has a very unique flame. Please note that based on the operator's prior burner experience, the flame settings may not look or sound as expected. The unique flame properties of the torch demonstrate superior performance. As such, until the operator becomes familiar with these unique properties, he/she should test out reactions with glass to determine whether the flame is reducing, neutral, or oxidizing.
Soft Glass: (COE 90 and higher)
For use with soft glass, Carlisle recommends a candle or focal length of 3/8". On a neutral setting, this will present a flame that is very hot and provides radiant heat around the flame. This radiant heat lessens the frequency of glass fractures due to temperature changes while moving in and out of the flame.
Hard Glass (aka Borosilicate COE 33):
For use with hard glass, Carlisle recommends a candle or focal length of 3/4". Please note that a neutral setting of this flame may produce orange tips on the candles. However, as long as the candles are all the same length, this should not produce reduction on borosilicate colors.
Oxygen Use:
Once a Neutral flame is achieved, adding more oxygen will produce the Oxidizing flame. An oxidizing flame will make a more narrow flame pattern that can be used for more delicate work. It is important to note that the extra oxygen also has a cooling effect in the flame and will lower the heat potential.
Gas Equipment
for lampworkers, Glass Beadmakers and Glassblowers
Click Here to see our Oxygen Concentrators (Oxygen Generators)
Gas Regulators
Two regulators are required when you use a two gas, (oxygen and propane) torch. They fit between the gas tanks and the gas hose. None are needed if you are using the Hot Head torch. Oxygen Regulator is not needed if you are using an Oxygen Concentrator.| Item# | Description | Price |
 |
OXYGEN REGULATOR Two gauge. One Stage - Click Here for information about regulators, about OUR regulators and warranty. Inlet CGA 540. Outlet male "B" fitting. Order Number REB93 | $69.00 |
 |
FUEL GAS REGULATOR - Propane, Propylene, or Acetylene Two gauge. One Stage - Click here for information about regulators, about OUR regulators and warranty. Inlet CGA 510. Outlet male "B" fitting. Order Number REB11 | $69 |
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS.
Gas Hoses
Use this
hose when you use a two gas torch (oxygen and propane) like a Minor Burner.
To attach torch, push the cut ends onto the torch and secure with a hose clamp. These
hoses have two attached hoses, one for oxygen and one for propane. The brass end
of the hoses are attached to the gas regulators. Propane hose fittings are left handed threads and colored red and oxygen is right handed
and colored green - This prevents a mix-up when attaching hoses. CAUTION Do not use the easy to find oxygen/acetylene type hoses. The propane gas will rot them. The hoses we sell are made for all types of gas including propane. Hose ends have female brass fittings.
| Item# | Length | Ends of hose - hose diameter | Price |
| T124 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side 1/4" diameter hose |
$22
|
| T254 | 25 ft (7.7 meters) |
Female "B" fitting on both ends 1/4" diameter hose |
$34
|
The below larger diameter hose is only used if when you need a large hose to fit over the large inlet fittings on some torches. (You can get the smaller 1/4" hose listed above on these large inlet fittings with a bit of effort. A trick is to immerse the end of the hose in very hot water to soften the end.)
Order # |
Length | Ends of hose - hose diameter | Price |
| T128 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side 3/8" diameter hose |
$29.50
|
| T258 | 25 ft (7.7 meters) | Female "B" fitting on both ends 3/8" diameter hose |
$52.00
|
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS
Y - Connectors for Hose
Y Connector -
Connect this fitting at the output of the regulator and attach two hoses so you can use two torches from the same tank.
Oxygen and propane Y are packaged and priced separately.Y Connector with valves - Same as the Y connector described above except has two on/off valves, one for each hose.
| Item# | Description | Output end is a | Input end is a | Price |
| 101 | Y hose connector (oxygen) | hose (B fitting) | Oxygen regulator | $19.50
|
| 102 | Y hose connector (propane) | hose (B fitting) | Propane regulator | $19.50
|
| 101V | Y hose connector with valve (Oxygen) | hose (B fitting) | Oxygen regulator | $32.50
|
| 102V | Y hose connector with valve (Propane) | hose (B fitting) | Propane regulator | $32.50
|
* The FA30 connects between the regulator and the gas hose and is more commonly used.
Flashback Arrestors
In some rare situations, a flame can travel back down a hose to the gas tank and cause an explosion.
This device helps prevent this reverse gas flow and flashback by using a reverse flow check valve and a flame arrestor.
Packaged and priced with both an oxygen and a propane arrestor.
| Item# | Description | Output end is a | Input end is a | Price |
| Flashback arrestors (pair of oxygen and fuel gas) Connects directly to the fittings on a torch like the 3AB, 8M and Carlisle. We also include the fitting so you can put this arrestor in the middle of your twin hose. A good place to put this arrestor is a couple feet away from the torch. If you cut the hose you will not have fittings on the ends. Then must order one or two pair of A2 fittings for $5.00 to connect to arrestor. FA10 |
Female B size hose fitting Male B size fitting using the included adaptor |
Male B size hose fitting | $54.00
|
|
| Flashback arrestors (pair of oxygen and fuel gas) Connects directly on the regulator. Item #FA30 | Male B size gas hose fitting | Female B size gas hose fitting | $54.00
|
|
 |
Insert into cut end of hose and secure with included hose clamp. Check for leaks. Item #A214 | One side Female B size hose fitting | Other side a barb that fits in a 1/4" ID gas hose - use a hose clamp | $5.00
|
 |
Insert into cut end of hose and secure with included hose clamp. Check for leaks. Item #A338 | One side Female B size hose fitting | Other side a barb that fits in a 3/8" ID gas hose - use a hose clamp | $5.00
|
|
Oxygen and Fuel Gas Fittings - The pieces in the picture labeled "included".
A pair of these are included in the FA10.
If you need extra pieces order the A30 and A31 parts. A30 ox A31 fuel |
Male B size gas hose fitting | Male B size gas hose fitting | A30 $1.50 each
A31 $1.50 ea
|
Note: Flashback arrestors have an arrow stamped on it to indicate the gas flow direction.
Works in only one direction.
A2 optional,
not always need and are not included.* The FA30 connects between the regulator and the gas hose and is more commonly used. Requires B size fittings on hose.
ALL IN ONE - 4 in 1
Combination Flashback Arrestor and Quick-Connect - Item# QDF30 - $79.00
Four Functions in a single item. Shorter and less expensive than if purchased separately.
|
Hose Quick Connects
Makes an easy job out of disconnecting and reconnecting your torch.Disconnect your torch switching to a different torch or to put it away for safe keeping.
Great for quick classroom set up and take down.
| Item# | Description | Input end is a | Output end is a | Price |
| QDB10 | Quick Connects (pair) | Male B gas hose fitting | Female B fitting | $49
|
| QDB20 | Quick Connects (pair) | Hose to Hose | Hose to Hose | $49
|
| QDB30 | Quick Connects (pair) | Regulator | Male B hose fitting | $49
|
Manifold Gas System
Connect up to six torches to the same gas supply with this manifold system.
Included are enough fittings and plugs to make 2 to 6 hose connections.
Two manifolds are required, one for oxygen and one for propane. All Brass.Custom Manifold Systems:
We can help you figure out which parts you would need for your system and pre assemble for no extra charge. Systems might also include quick connects and flashback arrestors. Place an order
| Item# | Description | Price |
| M6 | Manifolds system, Includes 1 block, 7 fittings and 4 plugs - two required - specify Oxygen or Propane | $57.50
|
| Item# | Description | Price |
| MB7 | Manifold block only, works with oxygen or gas | $39.00
|
| 32 | Extra Fitting - one side fits in the manifold block, other side fits a standard right handed thread oxygen "B" size hose fitting. | $1.50
|
| 33 | Extra Fitting - one side fits in the manifold block, other side fits a standard left handed thread gas "B" size hose fitting. Gas fittings have a "line notch" stamped into the nut part of the fitting to identify it as left handed threading. | $1.50
|
| P41P | Extra Plug - plugs unused outlets in the manifold block | $2.00
|
Manifold setup for 3 torches.Spark Lighter
Use to light torches. Squeeze the handles together to cause a spark. Place an order| Order# | Description | Price |
| 1501 | Used to light torches. Squeeze the handles together to cause a spark. | $3.00
|
Click here to see our foot pedals
Work Surfaces
for
Torch Lampworking, Glassblowing and
Glass Beadmaking
Work Surfaces
Protect your work table.
A comfortable pair of padded foam armrests
and worksurface and rod rest all in one! All stainless steel.
Pictured with a Minor Burner not included.
Dimensions are usually close but can vary a bit - plus or minus a 1/2" or so.
| Size | Description | Price | |
 |
#1617 12"x 13" |
Stainless Steel Work Surface - 12" x 13" flat area, heavy .030" thick metal. One edge is bent so you can wrap it over the edge of your work bench. The far edge is also bent up right so you have a nice 9" long rest for your colored glass rods. | $16
|
 |
#1644 13" x 18" |
Stainless Steel Work Surface - 13" x 18" flat area, heavy thick metal. Actually a bit smaller so we can fit it in a standard box. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 18" long rest for your colored glass rods. May need to be sent in it's own box. | $24 |
 |
#1636 17" x 18" |
Stainless Steel Work Surface - 17" x 18" flat area, heavy thick metal. Actually a bit smaller so we can fit it in a standard box. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 18" long rest for your colored glass rods. May need to be sent in it's own box. | $29
|
 |
#1655 16"x 28" |
Stainless Steel work surface - actually 16" x 28" flat area, heavy thick metal. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 28" long rest for your colored glass rods. PLUS if this is shipped, it must go in it's own box. | $45 |
 |
#1643 14"x 28" |
Stainless Steel work surface with Arm rests and built on rod rest - 14" x 28" flat area. (Actually a bit smaller so we can fit it in a standard box.) PLUS if this is shipped, it must go in it's own box. | $55
|
Accessories pictured not included.
Glass Rod RestsThis movable rod rest is used to support glass rods to keep them up off the flame worker's workbench for easier grabbing, better organization, and to keep the glass rods cleaner. The rippled edge keeps the rods from rolling around. These durable stainless steel rod holders can also be placed inside a glass bead kiln to support your mandrels.
| Item# | Description | Price |
| #RRT8 - 8" Rod rest - fits inside 9" kilns or on your workbench | $5.00
|
|
| #RRT9 - 9" Rod rest - fits inside 10" kilns or on your workbench | $6.00
|
|
 |
#RRT8T - 8" Rod rest - Extra Tall for easy Grabbing - see below | $7.00
|
 |
#RRT9T - 9" Rod rest - Extra Tall for easy Grabbing - see below | $8.00
|
| #RRT12T - 12" Rod rest - Extra Tall for easy Grabbing - see below | $10.00
|
|
 |
#RRT17T - 17" Rod rest - Extra Tall for easy Grabbing - see below | $14.00
|
Difference between standard and tall rod rests.
Looking for something? Torches? Tools? Kilns?
Look in our index. Click on: Sitemap
