Oxygen Concentrators
Make your own Oxygen for Torches
Never use an oxygen tank again!
With an oxygen concentrator (also known as an oxygen generator), oxygen
is pulled out of the air.
An oxygen regulator is not needed with concentrators. The
EX5, EX10 and EX15 units are refurbished and enhanced to increase oxygen
volume and pressure.
All concentrators are dropped shipped from the manufacturer. Small units can take 4-6 weeks while the larger units can take from 8-12 weeks.
But often sooner. Please allow time for delivery. Only $60 for shipping, handling, boxing, insurance to lower 48 for Extreme Oxygen Products.
Larger Units like the H-1 do not qualify for flat rate shipping
and need to be calculated by our customer service rep. All units have a 3 year warranty; provided regular and routine maintenance is performed.
Click here for information on setting up your Concentrator
Because the EX5, EX10 and EX15 are refurbished units, the color or
style may be different than what is pictured. The quality you expect will not be hindered by these changes!
Product Summary/Specifications
Extreme Oxygen's Spec Sheet
|
Operating Pressure |
Flow per Minute |
Flow per Hour |
Purity |
Soft Glass |
Small Boro |
Medium Boro |
Large Boro |
| EX-5 |
7 PSI |
5 LPM |
10.59 SCFH |
95% |
Y |
N |
N |
N |
| EX-10 |
10 PSI |
5 LPM |
10.59 SCFH |
95% |
Y |
Y |
N |
N |
| EX-15 |
15 PSI |
8 LPM |
16.94 SCFH |
95% |
Y |
Y |
Y |
N |
| H-1 |
20 PSI |
15 LPM |
31.77 SCFH |
95% |
Y |
Y |
Y |
Y |
Connecting Multiple Units
If you sere to use two or more units connected together, you
would increase the volume of air (Flow per Minute). You would
not increase the pressure, the pressure is limited by the unit
you select. Connecting two similar units together would not
quite double the volume. Connect the units with a brass Y
connector. Only connect similar units together, 8 PSI Machine with 8 PSI Machine's or
10 PSI Machine with 10 PSI Machine's. Do not connect say an 8 PSI Machine with and 10 PSI Machine. We carry
all of the hose and fittings you would need. Remember you do not
need an Oxygen Regulator when using these concentrators.
Noise Information
This is a very quiet brand compared to other brands we used to carry. The manufacture rates it at 50 db. This test would have been done in a sound proof room. But a true test is to measure it in a room with sound reflecting off walls and with normal background noise. We measured it under these conditions and it was 7 db above the background noise. In
laymen's terms we were amazed how quiet it is.
Oxygen Concentrators
|
Part # |
Our Low Price |
EX-5 |
EX-5 |
List Price
$345
Our Low Price $299
Flat $60 Shipping Fee for this item
within the Continental U.S. (Alaska, Hawaii, International orders call or email for quotes)
Equipment Set Up Instructions
|
EX-10
|
EX-10 |
List Price
$464
Our Low Price $429
Flat $60 Shipping Fee for this item
within the Continental U.S. (Alaska, Hawaii, International orders call or email for quotes)
Equipment Set Up Instructions
|
EX-15
|
EX-15 |
List Price
$695
Our Low Price $655
Flat $60 Shipping Fee for this item
within the Continental U.S. (Alaska, Hawaii, International orders call or email for quotes)
Equipment Set Up Instructions
|
H-1
|
H-1 |
List Price $1560
Our Low Price $1250
This concentrator ships Truck Freight and will not be reflected in quoted shipping.
This unit may take from 8 to 12 weeks
to ship.
Equipment Set Up Instructions
|
Which concentrators will power what torches?
Extreme Oxygen's Chart
| |
EX-5 |
EX-10 |
EX-15 |
H-1 |
2 EX-15(linked) |
3 EX-15(linked) |
| Cricket |
0% |
90% |
100% |
100% |
100% |
100% |
| Mini CC |
0% |
90% |
100% |
100% |
100% |
100% |
| Nortel Minor |
100% |
100% |
100% |
100% |
100% |
100% |
| Piranha |
100% |
100% |
100% |
100% |
100% |
100% |
| Betta |
100% |
100% |
100% |
100% |
100% |
100% |
| Bobcat |
100% |
100% |
100% |
100% |
100% |
100% |
| Little Dragon |
N/A |
100% |
100% |
100% |
100% |
100% |
| Nortel Mid-Range |
N/A |
N/A |
N/A |
100% |
100% |
100% |
| Barracuda |
N/A |
N/A |
N/A |
95% |
96% |
100% |
| Knight Bullet |
N/A |
N/A |
N/A |
95% |
95% |
100% |
| Phantom |
N/A |
N/A |
N/A |
90% |
95% |
100% |
| Tiger Shark |
N/A |
N/A |
N/A |
90% |
95% |
100% |
| Nortel Major |
N/A |
N/A |
N/A |
N/A |
N/A |
95% |
| Red Max |
N/A |
N/A |
N/A |
95% |
95% |
100% |
Attention International customers: Unless otherwise noted, all devices are only available in 120volts. Some of our customers have used transformers for these devices to work
with their country's voltage.
Gas Equipment
for lampworkers, Glass Beadmakers and Glassblowers
Click Here to see our Oxygen Concentrators (Oxygen Generators)
Gas Regulators
Two regulators are required when you use a two gas, (oxygen and propane) torch.
They fit between the gas tanks and the gas hose.
None are needed if you are using the Hot Head torch. Oxygen Regulator is
not needed if you are using an Oxygen Concentrator.
| Item# |
Description |
Price |
 |
OXYGEN REGULATOR
Two gauge. One Stage - Click Here for information about regulators, about OUR regulators and warranty.
Inlet CGA 540. Outlet male "B" fitting.
Order Number REB93
| $69.00
|
 |
FUEL GAS REGULATOR - Propane, Propylene, or Acetylene
Two gauge. One Stage - Click here for information about regulators, about OUR regulators and warranty.
Inlet CGA 510. Outlet male "B" fitting.
Order Number REB11
| $69
|
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS.
Gas Hoses
Use this
hose when you use a two gas torch (oxygen and propane) like a Minor Burner.
To attach torch, push the cut ends onto the torch and secure with a hose clamp. These
hoses have two attached hoses, one for oxygen and one for propane. The brass end
of the hoses are attached to the gas regulators. Propane hose fittings are left handed threads and colored red and oxygen is right handed
and colored green - This prevents a mix-up when attaching hoses.
CAUTION
Do not use the easy to find oxygen/acetylene type hoses. The propane gas
will rot them. The hoses we sell are made for all types of gas including
propane. Hose ends have female brass fittings.
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS
Y - Connectors for Hose
Y Connector -
Connect this fitting at the output of the regulator and attach two hoses so you can use two torches from the same tank.
Oxygen and propane Y are packaged and priced separately.
Y Connector with valves - Same as the Y connector described above except has two on/off valves, one for each hose.
| Item# |
Description |
Output end is a |
Input end is a |
Price |
| 101 |
Y hose connector (oxygen) |
hose (B fitting) |
Oxygen regulator |
$19.50
|
| 102 |
Y hose connector (propane) |
hose (B fitting) |
Propane regulator |
$19.50
|
| 101V |
Y hose connector with valve (Oxygen) |
hose (B fitting) |
Oxygen regulator |
$32.50
|
| 102V |
Y hose connector with valve (Propane) |
hose (B fitting) |
Propane regulator |
$32.50
|
* The FA30 connects between the regulator and the gas hose and is more commonly used.
Flashback Arrestors
In some rare situations, a flame can travel back down a hose to the gas tank and cause an explosion.
This device helps prevent this reverse gas flow and flashback by using a reverse flow check valve and a flame arrestor.
Packaged and priced with both an oxygen and a propane arrestor.
Note: Flashback arrestors have an arrow stamped on it to indicate the gas flow direction.
Works in only one direction.
A2 optional,
not always need and are not included.
* The FA30 connects between the regulator and the gas hose and
is more commonly used. Requires B size fittings on hose.
ALL IN ONE - 4 in 1
Combination Flashback Arrestor and Quick-Connect - Item# QDF30 - $79.00
Four Functions in a single item. Shorter and less expensive than if purchased separately.
- A flashback arrestor
- A quick connect and disconnect
- An automatic shutoff valve
- An internal reverse flow check valve all
|
Hose Quick Connects
Makes an easy job out of disconnecting and reconnecting your torch.
Disconnect your torch switching to a different torch or to put it away for safe keeping.
Great for quick classroom set up and take down.
| Item# |
Description |
Input end is a |
Output end is a |
Price |
| QDB10 |
Quick Connects (pair) |
Male B gas hose fitting |
Female B fitting |
$49
|
| QDB20 |
Quick Connects (pair) |
Hose to Hose |
Hose to Hose |
$49
|
| QDB30 |
Quick Connects (pair) |
Regulator |
Male B hose fitting |
$49
|
Manifold Gas System
Connect up to six torches to the same gas supply with this manifold system.
Included are enough fittings and plugs to make 2 to 6 hose connections.
Two manifolds are required, one for oxygen and one for propane. All Brass.
Custom Manifold Systems:
We can help you figure out which parts you would need for your system and pre assemble for no extra charge.
Systems might also include quick connects and flashback arrestors.
Place an order
| Item# |
Description |
Price |
| M6 |
Manifolds system, Includes 1 block, 7 fittings and 4 plugs - two required - specify Oxygen or Propane |
$57.50
|
| Item# |
Description |
Price |
| MB7 |
Manifold block only, works with oxygen or gas |
$39.00
|
| 32 |
Extra Fitting - one side fits in the manifold block, other side fits a standard right handed thread oxygen
"B" size hose fitting. |
$1.50
|
| 33 |
Extra Fitting - one side fits in the manifold
block, other side fits a standard left handed thread gas "B"
size hose fitting. Gas fittings have a "line notch"
stamped into the nut part of the fitting to identify it as left handed threading. |
$1.50
|
| P41P |
Extra Plug - plugs unused outlets in the manifold block |
$2.00
|
Manifold setup for 3 torches.
Spark Lighter
Use to light torches. Squeeze the handles together to cause a spark.
Place an order
| Order# |
Description |
Price |
| 1501 |
Used to light torches. Squeeze the handles together to cause a spark. |
$3.00
|
Click here to see our foot pedals
Work Surfaces
for
Torch Lampworking, Glassblowing and
Glass Beadmaking
Work Surfaces
Protect your work table.
A comfortable pair of padded foam armrests
and worksurface and rod rest all in one! All stainless steel.
Pictured with a Minor Burner not included.
Dimensions are usually close but can vary a bit - plus or minus a 1/2"
or so.
|
Size |
Description |
Price |
 |
#1646
10.5"x 11" |
Stainless Steel Work Surface - 10.5" x 11"
flat area, heavy .030" thick metal. One edge is bent so
you can wrap it over the edge of your work bench. The far edge
is also bent up right so you have a nice 9" long rest for
your colored glass rods. Made in the USA |
$15
|
 |
#1644
13" x 18" |
Stainless Steel Work Surface - 13" x
18" flat area, heavy thick metal. Actually a bit smaller so we can
fit it in a standard box. Front edge is bent so
it fits nicely over the edge of your work table. The far edge
is also bent up right so you have a nice 18" long rest for your colored
glass rods. May need to be sent in it's own box. Made in the USA |
$24
|
 |
#1636
18" x 18" |
Stainless Steel Work Surface - 18" x
18" flat area, heavy thick metal. Actually a bit smaller so we can
fit it in a standard box. Front edge is bent so
it fits nicely over the edge of your work table. The far edge
is also bent up right so you have a nice 18" long rest for your colored
glass rods. May need to be sent in it's own box. Made in the USA |
$29
|
 |
#1655
16"x
28" |
Stainless Steel work surface - actually 16"
x 28" flat area, heavy thick metal. Front edge is bent
so it fits nicely over the edge of your work table. The far edge
is also bent up right so you have a nice 28" long rest for
your colored glass rods. PLUS if this is shipped, it must go
in it's own box. Made in the USA |
$45
|
|
|
#1649
16"x 36" |
Stainless Steel work surface - actually 16"
x 36" flat area, heavy thick metal. Front edge is bent
so it fits nicely over the edge of your work table. The far edge
is also bent up right so you have a nice 36" long rest for
your colored glass rods. PLUS if this is shipped, it must go
in it's own box. Made in the USA |
$45
|
 |
#1643
14"x 28" |
Stainless Steel work surface
with Arm rests and built on rod rest - 14" x 28" flat area. (Actually a bit smaller so we can fit it in a standard box.) PLUS if this is shipped, it must go in it's own box. Made in the USA |
$55
|
 |
#1656
24"x 36" |
Stainless Steel work surface
with Arm rests and a 36" built on rod rest - 24" x 36" flat area. PLUS if this is shipped, it must go in it's own box.
Made in the USA |
$75
|
Accessories pictured not included.
Glass Rod Rests
This movable rod rest is used to support glass rods to keep them up off the flame worker's workbench for easier grabbing, better organization, and to keep the glass rods cleaner.
The rippled edge keeps the rods from rolling around.
These durable stainless steel rod holders can also be placed inside a glass bead kiln to support your mandrels.
| Item# |
Description |
Price |
| |
#RRT8 - 8" Rod rest - fits inside 9" kilns or on your workbench
Made in the USA |
$6.00
|
| |
#RRT9 - 9" Rod rest - fits inside 10" kilns or on your workbench
Made in the USA |
$7.00
|
 |
#RRT8T - 8" Rod rest -
Extra Tall for easy Grabbing - see below
Made in the USA |
$7.00
|
 |
#RRT9T - 9" Rod rest - Extra Tall for easy Grabbing - see below
Made in the USA |
$8.00
|
| |
#RRT12T - 12" Rod rest -
Extra Tall for easy Grabbing - see below
Made in the USA |
$10.00
|
 |
#RRT17T - 17" Rod rest - Extra Tall for easy Grabbing - see below
Made in the USA |
$14.00
|
Difference
between standard and tall rod rests.
Looking for something? Torches? Tools? Kilns?
Look in our index. Click on: Sitemap
Order Now
