Order Now
Mid Range Burner and Accessories
for Glass Lampworkers, Beadmakers,
Flameworkers, Glassblowers and Marblemakers
Choose between three varietiesBottom Tip/Flame is the same on all three varieties.
The Midrange bench Burner
by Nortel.
The bottom tip is Adjustable!. With a single set of oxygen and gas valves, you can get a fairly small pointed flame or a larger bushy flame by adjusting the valves.
You need the following equipment to use this torch:
|
REMEMBER
- Surface Mix Tip works with all kinds of glass. Soft and Hard.
- Pre-Mix Mix Tips only work with Borosilicate Hard Glass (Pyrex) but is faster working.
| Order# | Description | Price |
| 16025 | Mid Range Burner - one tip | $269 |
| 16026 | Mid Range Burner - with extra surface mix top torch - the Minor Burner | $379 |
| 16028 | Mid Range Burner - with extra surface mix top torch - The Mega Minor Burner - Not pictured but looks like 16026 | $424 |
| 16027 | Mid Range Burner - with extra pre-mix top torch - extra tips listed below - Tip Included | $379 |
| 1402 | Torch Mounted Marvering Pad puts a graphite marvering pad in your work area close to the flame. Slightly tilted so pieces don't roll off. Edge can be used for shaping! |
$24 |
Optional TIPS for the 16027
The other 3 torched do not use these tips.
Single Orifice
Thread size 7/16-24
| Order # |
Description | Hole size in inches | Price |
| OX-00 | One Hole - Smallest size | .020 | $19 |
| OX-0 | One Hole - Smallest size | .032 | $17 |
| OX-1 | One Hole | .042 | $15 |
| OX-2 | One Hole | .055 | $12 |
| OX-3 | One Hole | .07 | $12 |
| OX-4 | One Hole | .082 | $12 |
| OX-5 | One Hole - Largest size | .1 | $12 |
Multiple Orifice
| Order# | Description | Price |
| HTM-0 | 7 holes - each .04 inch diameter holes | $31 |
| HTM-1 | 9 holes - each .04 inch diameter holes | $31 |
| HTM-2 | 9 holes - each .048 inch diameter holes | $31 |
| HTM-03 | 9 holes - each .055 inch diameter holes | $31 |
| Order# | Description | Price |
| HTC-0 | 7 holes - Silent Burn | $30 |
| HTC-1 | 12 holes - Silent Burn | $32 |
| HTC-2 | 19 holes - Silent Burn | $37 |
| HTC-3 | 31 holes - Silent Burn click here to see the HT3 tip fired up |
$42 |
CAUTION - all tips are subject to burning out if you have an improper torch adjustment. The HT-2 and HT-3 are the most sensitive tips to burning out and these are not recommended for beginners who are learning how to adjust their torches properly - therefore these and all tips are not guaranteed from burn out. Please see the person who instructed you to learn the proper torch adjustment.
Gas Equipment
Click Here to see our Oxygen Concentrators (Oxygen Generators)
Gas Regulators
Two regulators are required when you use a two gas, (oxygen and propane) torch like a Minor Burner.
They fit between the gas tanks and the gas hose.
None are needed if you are using the Hot Head torch.Click Here for an important choice you need to make
| Item# | Gas | Description | Price |
| REB93 | Oxygen | Two gauge. One Stage - Click Here for warranty. Inlet CGA 540. Outlet male "B" fitting | $69.00 |
| REB11 | Propane | Two gauge. One Stage - Click here for warranty. Inlet CGA 510. Outlet male "B" fitting | $69.00 |
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS.
Gas Hoses
Use this
hose when you use a two gas torch (oxygen and propane) like a Minor Burner.
To attach torch, push the cut ends onto the torch and secure with a hose clamp. These
hoses have two attached hoses, one for oxygen and one for propane. The brass end
of the hoses are attached to the gas regulators. Propane hose fittings are left handed threads and colored red and oxygen is right handed
and colored green - This prevents a mix-up when attaching hoses. CAUTION Do not use the easy to find oxygen/acetylene type hoses. The propane gas will rot them. The hoses we sell are made for all types of gas including propane. Hose ends have female brass fittings.
| Item# | Length | Ends of hose - hose diameter | Price |
| T124 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side - 1/4" diameter hose | $22.00 |
| T254 | 25 ft (7.7 meters) | Female "B" fitting on both ends - 1/4" diameter hose | $34.00 |
The below larger diameter hose is only used if when you need a large hose to fit over the large inlet fittings on some torches. (You can get the smaller 1/4" hose listed above on these large inlet fittings with a bit of effort. A trick is to immerse the end of the hose in very hot water to soften the end.)
Order # |
Length | Ends of hose - hose diameter | Price |
| T128 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side - 3/8" diameter hose | $29.50 |
| T258 | 25 ft (7.7 meters) | Female "B" fitting on both ends - 3/8" diameter hose | $52.00 |
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS
Y - Connectors for Hose
Y Connector -
Connect this fitting at the output of the regulator and attach two hoses so you can use two torches from the same tank.
Oxygen and propane Y are packaged and priced separately.Y Connector with valves - Same as the Y connector described above except has two on/off valves, one for each hose.
| Item# | Description | Output end is a | Input end is a | Price |
| 101 | Y hose connector (oxygen) | hose (B fitting) | Oxygen regulator | $19.50 |
| 102 | Y hose connector (propane) | hose (B fitting) | Propane regulator | $19.50 |
| 101V | Y hose connector with valve (Oxygen) | hose (B fitting) | Oxygen regulator | $32.50 |
| 102V | Y hose connector with valve (Propane) | hose (B fitting) | Propane regulator | $32.50 |
* The FA30 connects between the regulator and the gas hose and is more commonly used.
Flashback Arrestors
In some rare situations, a flame can travel back down a hose to the gas tank and cause an explosion.
This device helps prevent this reverse gas flow and flashback by using a reverse flow check valve and a flame arrestor.
Packaged and priced with both an oxygen and a propane arrestor.
| Item# | Description | Output end is a | Input end is a | Price |
| FA10 | Flashback arrestors (pair of oxygen and fuel gas) Connects directly to the fittings on a torch like the 3AB, 8M and Carlisle. We also include the fitting so you can put this arrestor in the middle of your twin hose. A good place to put this arrestor is a couple feet away from the torch. If you cut the hose you will not have fittings on the ends. Then must order one or two pair of A2 fittings for $5.00 to connect to arrestor. |
Female B size hose fitting Male B size fitting using the included adaptor |
Male B size hose fitting | $54.00 |
| FA30 | Flashback arrestors (pair of oxygen and fuel gas) Connects directly on the regulator. | Male B size gas hose fitting | Female B size gas hose fitting | $54.00 |
| A2 | Insert into cut end of hose and secure with hose clamp. Check for leaks. | One side Female B size hose fitting | Other side a barb that fits in a 1/4" ID gas hose - use a hose clamp | $5.00 |
| A30 ox A31 fuel |
Oxygen and Fuel Gas Fittings - The pieces in the picture labeled "included". A pair of these are included in the FA10. If you need extra pieces order the A30 and A31 parts. | Male B size gas hose fitting | Male B size gas hose fitting | $1.50 each |
Note: Flashback arrestors have an arrow stamped on it to indicate the gas flow direction. Works in only one direction.
A2 optional, not included.* The FA30 connects between the regulator and the gas hose and is more commonly used. Requires B size fittings on hose.
ALL IN ONE - 4 in 1
Combination Flashback Arrestor and Quick-Connect - Item# QDF30 - $79.00
Four Functions in a single item. Shorter and less expensive than if purchased separately.
|
Hose Quick Connects
Makes
an easy job out of disconnecting and reconnecting your torch.Disconnect your torch switching to a different torch or to put it away for safe keeping.
Great for quick classroom set up and take down.
| Item# | Description | Input end is a | Output end is a | Price |
| QDB10 | Quick Connects (pair) | Male B gas hose fitting | Female B fitting | $49 |
| QDB20 | Quick Connects (pair) | Hose to Hose | Hose to Hose | $49 |
| QDB30 | Quick Connects (pair) | Regulator | Male B hose fitting | $49 |
Manifold Gas System
Connect up to six torches to the same gas supply with this manifold system.
Included are enough fittings and plugs to make 2 to 6 hose connections.
Two manifolds are required, one for oxygen and one for propane. All Brass.Custom Manifold Systems:
We can help you figure out which parts you would need for your system and pre assemble for no extra charge. Systems might also include quick connects and flashback arrestors. Place an order
| Item# | Description | Price |
| M6 | Manifolds system, Includes 1 block, 7 fittings and 4 plugs - two required - specify Oxygen or Propane | $57.50 |
| Item# | Description | Price |
| MB7 | Manifold block only, works with oxygen or gas | $39.00 |
| 32 | Extra Fitting - one side fits in the manifold block, other side fits a standard right handed thread oxygen "B" size hose fitting. | $1.50 |
| 33 | Extra Fitting - one side fits in the manifold block, other side fits a standard left handed thread gas "B" size hose fitting. Gas fittings have a "line notch" stamped into the nut part of the fitting to identify it as left handed threading. | $1.50 |
| P41P | Extra Plug - plugs unused outlets in the manifold block | $2.00 |
Manifold setup for 3 torches.Bulk Adaptor Systems
For users of Hot Head Torches or any torches similar to the HotHead torchSave on the cost of propane by using a large bulk refillable propane tank instead of the small disposable fuel gas cylinders.
Item# F273701 uses a single hose with the correct fittings on each end. 5 or 12 foot hose.
Y-Propane F271735 - Connect two torches with this fitting. This Y fits into a bulk tank - the two other ends fit two F273701 hoses which go to the Hot Head torches.| Item# | Description | Price |
| F273701 | Bulk adaptor system - 5 Feet | $27 |
| F273710 | Bulk adaptor system - 12 Feet | $42 |
| F271735 | Y-Propane Fitting | $32 |
Spark Lighter
Use to light torches. Squeeze the handles together to cause a spark. Place an order| Order# | Description | Price |
| 1501 | Useed to light torches. Squeeze the handles together to cause a spark. | $2.00 |
All stainless steel.
Holds your propane bottle safely and at the correct angle for your torch.
Torch and propane tank not included.
We recommend the HotHead torch.
Includes a built in tool and glass rod rest.
Holder holds both the wide and narrow shaped gas tank.
Should be clamped or screwed to the table.
Work Surfaces
Catalogs
