Order Now
Carlisle CC Plus Torches
For Glass Lampworkers, Beadmakers,
Flameworkers, Glassblowers and Marblemakers
Carlisle CC Plus Glass Torches are
Pre Mix Center fire with a Surface Mix Outer Burner
Carlisle CC Plus
| Order# | Description | Price |
 |
IN STOCK - Ready to Ship CC Plus with Ball & Post Mount With #3 Center Fire - 2 Inlet Item #83BP2 |
$2145
|
|
|
IN STOCK - Ready to Ship CC Plus with Ball & Post Mount With #3 Center Fire - 4 Inlet for Foot Peddle Item #65BP4 |
$2145 |
 |
IN STOCK - Ready to Ship CC Plus with Rack & Pinion Mount With #3 Center Fire - 2 Inlet Item #65RP2 |
$2372
|
|
|
IN STOCK - Ready to Ship CC Plus with Rack & Pinion Mount With #3 Center Fire - 4 Inlet for Foot Peddle Item #83RP4 |
$2372
|
|
|
IN STOCK - Ready to Ship CC Plus with Ball & Post Mount With #5 Center Fire - 2 Inlet Item #85BP2 |
$2145
|
|
|
IN STOCK - Ready to Ship CC Plus with Ball & Post Mount With #5 Center Fire - 4 Inlet for Foot Peddle Item #85BP4 |
$2145
|
|
|
IN STOCK - Ready to Ship CC Plus with Rack & Pinion Mount With #5 Center Fire - 2 Inlet Item #85RP2 |
$2372
|
|
|
IN STOCK - Ready to Ship CC Plus with Rack & Pinion Mount With #5 Center Fire - 4 Inlet for Foot Peddle Item #85RP4 |
$2372
|
You need the following equipment to use this torch:
|
The Carlisle CC and CC Plus Burners are known as cannon style burners. Their large outer case and tremendous flame output resembles the profile of a "cannon". The CC burner is capable of producing 276,100 BTU/hr at 5 P.S.I. natural gas and 10 P.S.I. oxygen, while the CC Plus is able to produce 419,600 BTU/hr under the same pressures.
Both burners produce two distinctive flames, the center fire (pre-mixed) and the outer fire (surface mixed). The center fire, which has characteristics of a single ported tip, produces a pre-mixed flame similar to what may be achieved with a Carlisle hand torch. This center fire tip is standard with piloting. Depending on the fuel gases used, the center fire is available without piloting. Natural gas and propane use a piloted center fire tip, while an unpiloted tip must be used with hydrogen. The center fire produces a similar flame on both the CC and the CC Plus models and is essentially the same tip. The surface mixed outer fire consists of a set of stainless steel tubes that make up a matrix around the center fire. There are two concentric rings of tubes developing the outer fire of the CC burner, and three rings that produce the CC Plus outer fire.
The outer shell of the CC series body is manufactured from brass (SS optional). The brass shell is threaded onto a bronze machined casting, which represents the mixer body. For fuel gas supply, four metering valves are attached to the back of the mixer body. These valves are color coded for ease of use. The oxygen valves have a green handle while the gas valves have red handles. These valves are standard interconnected by crossover attachments to limit the feed hose requirements to two. The CC series is also available with four separate inlets to allow for the use of foot controllers. The standard connection type for this configuration is hose adapters. Other connection types are available such as welding hose and JIC connections. These connection types are explained further in the options and accessories section.
The CC series can accept and interchange several different styles of base attachments. The standard style is a Ball & Post mount. The Ball & Post utilizes the horseshoe shaped cast iron base with a ball and socket connection. The post that extends upward is threaded directly into the bottom of the CC mixer body. This style offers a selective articulation. In order to adjust the angle of the head, the user must manually release a thumb screw in the cast iron base. This provides positive burner positioning. The Rack & Pinion style mount utilizes a pinion gear to pivot the burner in an arc. This style offers greater range in positioning than the Ball & Post mount. The user can adjust a knob on the side of the mounting device for quick, accurate positioning. Custom lathe mounts are also available as an option.
The Heat Exchanger is standard with any CC series burner. Manufactured from aluminum, the Heat Exchanger dissipates heat from the burner body. The Heat Exchanger has cooling fins providing increased surface area for the transfer of heat. This keeps the burner cool during operation. Some applications with high radiant heat transfer, will find our water cooling option desirable.
Gas Equipment
for lampworkers, Glass Beadmakers and Glassblowers
Click Here to see our Oxygen Concentrators (Oxygen Generators)
Gas Regulators
Two regulators are required when you use a two gas, (oxygen and propane) torch. They fit between the gas tanks and the gas hose. None are needed if you are using the Hot Head torch. Oxygen Regulator is not needed if you are using an Oxygen Concentrator.| Item# | Description | Price |
 |
OXYGEN REGULATOR Two gauge. One Stage - Click Here for information about regulators, about OUR regulators and warranty. Inlet CGA 540. Outlet male "B" fitting. Order Number REB93 | $69.00 |
 |
FUEL GAS REGULATOR - Propane, Propylene, or Acetylene Two gauge. One Stage - Click here for information about regulators, about OUR regulators and warranty. Inlet CGA 510. Outlet male "B" fitting. Order Number REB11 | $69 |
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS.
Gas Hoses
Use this
hose when you use a two gas torch (oxygen and propane) like a Minor Burner.
To attach torch, push the cut ends onto the torch and secure with a hose clamp. These
hoses have two attached hoses, one for oxygen and one for propane. The brass end
of the hoses are attached to the gas regulators. Propane hose fittings are left handed threads and colored red and oxygen is right handed
and colored green - This prevents a mix-up when attaching hoses. CAUTION Do not use the easy to find oxygen/acetylene type hoses. The propane gas will rot them. The hoses we sell are made for all types of gas including propane. Hose ends have female brass fittings.
| Item# | Length | Ends of hose - hose diameter | Price |
| T124 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side 1/4" diameter hose |
$22
|
| T254 | 25 ft (7.7 meters) |
Female "B" fitting on both ends 1/4" diameter hose |
$34
|
The below larger diameter hose is only used if when you need a large hose to fit over the large inlet fittings on some torches. (You can get the smaller 1/4" hose listed above on these large inlet fittings with a bit of effort. A trick is to immerse the end of the hose in very hot water to soften the end.)
Order # |
Length | Ends of hose - hose diameter | Price |
| T128 | 12 ft (3.7 meters) | Female "B" fitting one side and cut end of hose other side 3/8" diameter hose |
$29.50
|
| T258 | 25 ft (7.7 meters) | Female "B" fitting on both ends 3/8" diameter hose |
$52.00
|
The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS
Y - Connectors for Hose
Y Connector -
Connect this fitting at the output of the regulator and attach two hoses so you can use two torches from the same tank.
Oxygen and propane Y are packaged and priced separately.Y Connector with valves - Same as the Y connector described above except has two on/off valves, one for each hose.
| Item# | Description | Output end is a | Input end is a | Price |
| 101 | Y hose connector (oxygen) | hose (B fitting) | Oxygen regulator | $19.50
|
| 102 | Y hose connector (propane) | hose (B fitting) | Propane regulator | $19.50
|
| 101V | Y hose connector with valve (Oxygen) | hose (B fitting) | Oxygen regulator | $32.50
|
| 102V | Y hose connector with valve (Propane) | hose (B fitting) | Propane regulator | $32.50
|
* The FA30 connects between the regulator and the gas hose and is more commonly used.
Flashback Arrestors
In some rare situations, a flame can travel back down a hose to the gas tank and cause an explosion.
This device helps prevent this reverse gas flow and flashback by using a reverse flow check valve and a flame arrestor.
Packaged and priced with both an oxygen and a propane arrestor.
| Item# | Description | Output end is a | Input end is a | Price |
| Flashback arrestors (pair of oxygen and fuel gas) Connects directly to the fittings on a torch like the 3AB, 8M and Carlisle. We also include the fitting so you can put this arrestor in the middle of your twin hose. A good place to put this arrestor is a couple feet away from the torch. If you cut the hose you will not have fittings on the ends. Then must order one or two pair of A2 fittings for $5.00 to connect to arrestor. FA10 |
Female B size hose fitting Male B size fitting using the included adaptor |
Male B size hose fitting | $54.00
|
|
| Flashback arrestors (pair of oxygen and fuel gas) Connects directly on the regulator. Item #FA30 | Male B size gas hose fitting | Female B size gas hose fitting | $54.00
|
|
 |
Insert into cut end of hose and secure with included hose clamp. Check for leaks. Item #A214 | One side Female B size hose fitting | Other side a barb that fits in a 1/4" ID gas hose - use a hose clamp | $5.00
|
 |
Insert into cut end of hose and secure with included hose clamp. Check for leaks. Item #A338 | One side Female B size hose fitting | Other side a barb that fits in a 3/8" ID gas hose - use a hose clamp | $5.00
|
|
Oxygen and Fuel Gas Fittings - The pieces in the picture labeled "included".
A pair of these are included in the FA10.
If you need extra pieces order the A30 and A31 parts. A30 ox A31 fuel |
Male B size gas hose fitting | Male B size gas hose fitting | A30 $1.50 each
A31 $1.50 ea
|
Note: Flashback arrestors have an arrow stamped on it to indicate the gas flow direction.
Works in only one direction.
A2 optional,
not always need and are not included.* The FA30 connects between the regulator and the gas hose and is more commonly used. Requires B size fittings on hose.
ALL IN ONE - 4 in 1
Combination Flashback Arrestor and Quick-Connect - Item# QDF30 - $79.00
Four Functions in a single item. Shorter and less expensive than if purchased separately.
|
Hose Quick Connects
Makes an easy job out of disconnecting and reconnecting your torch.Disconnect your torch switching to a different torch or to put it away for safe keeping.
Great for quick classroom set up and take down.
| Item# | Description | Input end is a | Output end is a | Price |
| QDB10 | Quick Connects (pair) | Male B gas hose fitting | Female B fitting | $49
|
| QDB20 | Quick Connects (pair) | Hose to Hose | Hose to Hose | $49
|
| QDB30 | Quick Connects (pair) | Regulator | Male B hose fitting | $49
|
Manifold Gas System
Connect up to six torches to the same gas supply with this manifold system.
Included are enough fittings and plugs to make 2 to 6 hose connections.
Two manifolds are required, one for oxygen and one for propane. All Brass.Custom Manifold Systems:
We can help you figure out which parts you would need for your system and pre assemble for no extra charge. Systems might also include quick connects and flashback arrestors. Place an order
| Item# | Description | Price |
| M6 | Manifolds system, Includes 1 block, 7 fittings and 4 plugs - two required - specify Oxygen or Propane | $57.50
|
| Item# | Description | Price |
| MB7 | Manifold block only, works with oxygen or gas | $39.00
|
| 32 | Extra Fitting - one side fits in the manifold block, other side fits a standard right handed thread oxygen "B" size hose fitting. | $1.50
|
| 33 | Extra Fitting - one side fits in the manifold block, other side fits a standard left handed thread gas "B" size hose fitting. Gas fittings have a "line notch" stamped into the nut part of the fitting to identify it as left handed threading. | $1.50
|
| P41P | Extra Plug - plugs unused outlets in the manifold block | $2.00
|
Manifold setup for 3 torches.Spark Lighter
Use to light torches. Squeeze the handles together to cause a spark. Place an order| Order# | Description | Price |
| 1501 | Used to light torches. Squeeze the handles together to cause a spark. | $3.00
|
Click here to see our foot pedals
Work Surfaces
for
Torch Lampworking, Glassblowing and
Glass Beadmaking
Work Surfaces
Protect your work table.
A comfortable pair of padded foam armrests
and worksurface and rod rest all in one! All stainless steel.
Pictured with a Minor Burner not included.
Dimensions are usually close but can vary a bit - plus or minus a 1/2" or so.
| Size | Description | Price | |
 |
#1617 12"x 13" |
Stainless Steel Work Surface - 12" x 13" flat area, heavy .030" thick metal. One edge is bent so you can wrap it over the edge of your work bench. The far edge is also bent up right so you have a nice 9" long rest for your colored glass rods. | $16
|
 |
#1644 13" x 18" |
Stainless Steel Work Surface - 13" x 18" flat area, heavy thick metal. Actually a bit smaller so we can fit it in a standard box. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 18" long rest for your colored glass rods. May need to be sent in it's own box. | $24 |
 |
#1636 17" x 18" |
Stainless Steel Work Surface - 17" x 18" flat area, heavy thick metal. Actually a bit smaller so we can fit it in a standard box. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 18" long rest for your colored glass rods. May need to be sent in it's own box. | $29
|
 |
#1655 16"x 28" |
Stainless Steel work surface - actually 16" x 28" flat area, heavy thick metal. Front edge is bent so it fits nicely over the edge of your work table. The far edge is also bent up right so you have a nice 28" long rest for your colored glass rods. PLUS if this is shipped, it must go in it's own box. | $45 |
 |
#1643 14"x 28" |
Stainless Steel work surface with Arm rests and built on rod rest - 14" x 28" flat area. (Actually a bit smaller so we can fit it in a standard box.) PLUS if this is shipped, it must go in it's own box. | $55
|
Accessories pictured not included.
Glass Rod RestsThis movable rod rest is used to support glass rods to keep them up off the flame worker's workbench for easier grabbing, better organization, and to keep the glass rods cleaner. The rippled edge keeps the rods from rolling around. These durable stainless steel rod holders can also be placed inside a glass bead kiln to support your mandrels.
| Item# | Description | Price |
| #RRT8 - 8" Rod rest - fits inside 9" kilns or on your workbench | $5.00
|
|
| #RRT9 - 9" Rod rest - fits inside 10" kilns or on your workbench | $6.00
|
|
 |
#RRT8T - 8" Rod rest - Extra Tall for easy Grabbing - see below | $7.00
|
 |
#RRT9T - 9" Rod rest - Extra Tall for easy Grabbing - see below | $8.00
|
| #RRT12T - 12" Rod rest - Extra Tall for easy Grabbing - see below | $10.00
|
|
 |
#RRT17T - 17" Rod rest - Extra Tall for easy Grabbing - see below | $14.00
|
Difference between standard and tall rod rests.
Looking for something? Torches? Tools? Kilns?
Look in our index. Click on: Sitemap
